Box-section wall tray Box Template Generator
Box-section wall tray. Every wall is a hollow box section — up, across the top, back down inside and onto a glue tab — so the rim is a closed tube on all four sides. Far stiffer than a single or even a doubled wall, and there is no raw board anywhere on the top edge.
Not yet plate-checked. This template folds, closes and exports cleanly, but its blank has not yet been matched against the standard's own drawing in detail. Treat it as a starting point and check it before you spend anything.
What is Box-section wall tray?
Box-section wall tray is a folding carton with a glued side seam, closing at each end with a tuck, a lock or a glued flap. Every wall is a hollow box section — up, across the top, back down inside and onto a glue tab — so the rim is a closed tube on all four sides. Far stiffer than a single or even a doubled wall, and there is no raw board anywhere on the top edge.
Uses
- High-volume packing lines, since a pre-glued blank erects in one movement
Advantages
- Cut from a single blank, so there is one tool and one part to stock
- Arrives glued and flat, and erects quickly by hand or by machine
Disadvantages
- The glued joint sets the minimum order — short runs are rarely economical
Typical industries
- General packing and light manufacturing
Recommended board grades
Folding boxboard or solid bleached board, typically 250–450 microns. Heavier board for larger cartons, lighter where the carton is filled by machine.
At a glance
| Code | B49.20.00.00 |
| Family | Folding carton (ECMA) |
| Also known as | box section wall tray, buffer wall tray, glued |
| Blank size at this size | 372 × 304 mm |
| Panels | 21 |
| Creases | 20 |
Measured 0.833 against the p44 plate (a CHECK, not a match): the plate tapers each ply into the next on a diagonal and this steps it square.
Get the dieline
The generator draws this style to whatever dimensions you enter and exports it as a 1:1 PDF, an SVG, or a DXF with the cut, crease and perforation lines on separate layers. Nothing to sign up for.
Open B49.20.00.00 in the generatorOther codes in this group
- RTEReverse Tuck End (RTE)checked
- STEStraight Tuck End (STE)checked
- AUTOAuto-bottom (crash lock) carton
- SLEEVESleeve (open both ends)
- PILLOWPillow box
- TTSBTuck Top, Seal End Bottom
- SNAPSnap-lock bottom (1-2-3 bottom)
- SEALSeal End carton
- GABLEGable top carton
- AUTO-FAuto-bottom, tuck to frontchecked
- SKILLET-TTSkillet base, tuck topchecked
- RTE-INVInverted Reverse Tuck Endchecked
- B4050Four-corner tray with hinged lid
- SNAP-FSnap-lock bottom, tuck to frontchecked
- HEXHexagonal carton
- STE-FSame panel tuck, to frontchecked
- B1010Self-locking traychecked
- TTSB-FTuck Top (front), Seal End Bottom
- AUTO-SEALCrash lock base, sealed top
- B6121Four-corner hinged lid tray, webbed
- WEBTUCKWebbed tuck carton
- TAPERTapered display tray
- B4020In-fold tray, four corners gluedchecked
- WRAPNon-glued wrap
Browse every code, or read what the groups mean.
Related
- Every FEFCO code we build — all 244 of them, grouped.
- FEFCO codes explained — what the four digits mean and what each group covers.
- How to measure a box — inside, outside and crease-to-crease.
- Flutes and calipers — why board thickness changes the blank.