FEFCO 0901 Box Template Generator

Base pad. A flat panel sized to the floor of the case, used to stiffen the base or to protect the product from the bottom flaps.

What is FEFCO 0901?

FEFCO 0901 is a part that goes inside another box — a partition, pad, liner or corner piece — rather than a container in its own right. A flat panel sized to the floor of the case, used to stiffen the base or to protect the product from the bottom flaps.

Uses

• Transit and e-commerce packing, where the box is handled by a carrier
• Protecting or separating goods inside a larger case

Advantages

• Cut from a single blank, so there is one tool and one part to stock
• Cut from offcuts or lighter board than the outer case, so it adds little cost

Disadvantages

• No standard style suits every product; check the fit against a sample before committing to a tool

Typical industries

• General distribution and warehousing

Recommended board grades

Single wall B or C flute for partitions and pads. Where the fitment carries the load rather than the outer case, match or exceed the outer box’s board.

At a glance

Get the dieline

The generator draws this style to whatever dimensions you enter and exports it as a 1:1 PDF, an SVG, or a DXF with the cut, crease and perforation lines on separate layers. Nothing to sign up for.

Other interior fitments

Partitions, dividers, pads, liners and other components used inside another case.

• 0900Narrow pad (batten)
• 0902Transverse partition
• 0903Longitudinal partition
• 0904Liner sleeve, wrapped about the heightchecked
• 0905Liner sleeve, wrapped about the widthchecked
• 0906Liner sleeve, wrapped about the lengthchecked
• 0907Liner sleeve with a split seam, about the widthchecked
• 0908Liner sleeve with a split seam, about the heightchecked
• 0909Liner sleeve with a split seam, about the widthchecked
• 0910Liner sleeve with a split seam, about the lengthchecked
• 0911Tray liner with corner flapschecked
• 0912Tray liner, corner flap on the end wallchecked
• 0913Flanged liner sleeve with a split seamchecked
• 0914Liner sleeve with a lapped seamchecked
• 0920Liner and divider, double-thickness partitionchecked
• 0921Liner and divider, single-thickness partitionchecked
• 0929Two U-channel liners
• 0930Cross divider (two pieces)
• 0931Interlocking partition lattice
• 0932Partition set with folded corner posts
• 0933Interlocking partition set
• 0934Interlocking partition set, many cells
• 0935Interlocking partition set at two heights
• 0936Standing partition, doubled wall along the width
• 0937Standing partition, doubled wall along the length
• 0938Standing partition, doubled wall at full case height
• 0940Deck with double cells across the full widthchecked
• 0941Twin square tubes with a top bridgechecked
• 0942Deck with diagonally braced end cellschecked
• 0943Deck with concertina end cushionschecked
• 0944Deck on two triangular ribs
• 0945Deck with triangular end gussetschecked
• 0946Deck with closed end cellschecked
• 0947Twin channels under a raised bridge
• 0948Twin braced tubes with a dropped bridge
• 0949Pad with upturned flanges
• 0950Pad with three-ply edge rails
• 0951U-channel edge protectorchecked
• 0965Laminated pad
• 0966Laminated pad, multi-wall board
• 0967Stepped laminated pad
• 0970Angle edge protector (L profile)checked
• 0971Double-ply angle edge protectorchecked
• 0972Double-ply angle protector, outer plies overhanging
• 0973Triangular section with a doubled centre webchecked
• 0974Gull-wing section with a doubled centre webchecked
• 0975Chevron protector on two closed tubeschecked
• 0976Three-ply angle protectorchecked

Browse every code, or read what the groups mean.

Related

• Every FEFCO code we build — all 244 of them, grouped.
• FEFCO codes explained — what the four digits mean and what each group covers.
• How to measure a box — inside, outside and crease-to-crease.
• Flutes and calipers — why board thickness changes the blank.