FEFCO 0934 Box Template Generator

Interlocking partition set, cells against the walls. The same interlocking grid with one extra crossing tucked in at each end, so the outermost partitions stand hard against the walls of the case and the row of cells along each wall is narrower than the ones inside. The arrangement used for bottles, jars and glassware.

Not yet plate-checked. This template folds, closes and exports cleanly, but its blank has not yet been matched against the standard's own drawing in detail. Treat it as a starting point and check it before you spend anything.

What is FEFCO 0934?

FEFCO 0934 is a part that goes inside another box — a partition, pad, liner or corner piece — rather than a container in its own right. The same interlocking grid with one extra crossing tucked in at each end, so the outermost partitions stand hard against the walls of the case and the row of cells along each wall is narrower than the ones inside. The arrangement used for bottles, jars and glassware.

Uses

Transit and e-commerce packing, where the box is handled by a carrier
Protecting or separating goods inside a larger case
Jobs where the depth or the fit has to be adjusted after packing

Advantages

Locks closed without glue or tape, which saves a consumable and a step
Cut from offcuts or lighter board than the outer case, so it adds little cost

Disadvantages

Needs 8 separate pieces, so there is more than one tool and more than one part to handle
Hand-locking takes longer per box than a taped or glued closure

Typical industries

Drinks and bottled goods

Recommended board grades

Single wall B or C flute for partitions and pads. Where the fitment carries the load rather than the outer case, match or exceed the outer box’s board.

At a glance

Code	`0934`
Family	Corrugated (FEFCO)
Blank size at this size	363 × 1906 mm
Panels	8
Creases	0

Measured against p133 with scripts/plate-diff.py. AT THE CELL COUNT THE PLATE DRAWS — cols 4, rows 2, which is what the defaults here are — it scores 0.93 with cut 0.930 found / 1.000 extra, crease 1.000 / 1.000, silhouette 0.990. cutExtra of exactly 1.000 is the part that matters: every stroke this template draws is on the plate. The 0.070 of plate ink not covered is ONE segment, and it is not in the drawing. Rendering p133 shows 0934's W strip as a plain rectangle with three slots cut from the bottom edge and no diagonal anywhere, but the extracted reference carries a 77.9-long diagonal from (0.111,0.500) to (1.000,1.000) — 6.8 per cent of the page's ink for this code, against 0.0 per cent off-axis on 0933's plate beside it. The sweep records the lower 0.784 because the fit wanders to rows=4, which puts five slots on a strip the plate gives three and costs cutExtra 0.216; rows is a parameter because the plate itself says the cell count is defined by the user, so it stays searchable. What separates this from 0933 is the extra crossing tucked in at each end: extracted slot centres on the W strip are 0.1105, 0.500 and 0.8895 of its length, where an even division would put them at 0.25, 0.50 and 0.75.

Get the dieline

The generator draws this style to whatever dimensions you enter and exports it as a 1:1 PDF, an SVG, or a DXF with the cut, crease and perforation lines on separate layers. Nothing to sign up for.

Open 0934 in the generator

Other interior fitments

Partitions, dividers, pads, liners and other components used inside another case.

Browse every code, or read what the groups mean.

Every FEFCO code we build — all 244 of them, grouped.
FEFCO codes explained — what the four digits mean and what each group covers.
How to measure a box — inside, outside and crease-to-crease.
Flutes and calipers — why board thickness changes the blank.