FEFCO 0412 Box Template Generator
Folder with tucked-in end walls. A ½W, H, W, H, ½W wrap with no corner tabs and nothing at all on the two ½W panels. Each end closes as a single piece hinged off the base: a band the width of the base with a square wing creased to it on either side, and beyond the band a second crease carrying a tapered return out to about half the base width. The wings are slit from the wall panels, so the whole assembly folds down inside the box as one, which is what holds the ends square before the top flaps come over.
Not yet plate-checked. This template folds, closes and exports cleanly, but its blank has not yet been matched against the standard's own drawing in detail. Treat it as a starting point and check it before you spend anything.
What is FEFCO 0412?
FEFCO 0412 is cut and creased from a single blank that folds up around the product, usually without a glued joint. A ½W, H, W, H, ½W wrap with no corner tabs and nothing at all on the two ½W panels. Each end closes as a single piece hinged off the base: a band the width of the base with a square wing creased to it on either side, and beyond the band a second crease carrying a tapered return out to about half the base width. The wings are slit from the wall panels, so the whole assembly folds down inside the box as one, which is what holds the ends square before the top flaps come over.
Uses
- General packing where a simple, economical board box is wanted
Advantages
- Cut from a single blank, so there is one tool and one part to stock
- Locks closed without glue or tape, which saves a consumable and a step
Disadvantages
- Hand-locking takes longer per box than a taped or glued closure
Typical industries
- General packing and light manufacturing
Recommended board grades
Single wall B or E flute. E flute where the outside will be printed, since the finer flute takes a cleaner print and creases more sharply.
At a glance
| Code | 0412 |
| Family | Corrugated (FEFCO) |
| Blank size at this size | 572 × 526 mm |
| Panels | 13 |
| Creases | 12 |
Get the dieline
The generator draws this style to whatever dimensions you enter and exports it as a 1:1 PDF, an SVG, or a DXF with the cut, crease and perforation lines on separate layers. Nothing to sign up for.
Open 0412 in the generatorOther folder boxes and trays
Usually one piece of board. The bottom is hinged to form two or all side walls and the cover; locking tabs, handles and display panels can be incorporated.
- 0400Wrap-around folder with an inner bottom liner
- 0401One-piece folder, plain ends
- 0402One-piece folder, flaps all roundchecked
- 0403Tray with box-section side wallschecked
- 0404Two crossed folderschecked
- 0405Two crossed folders, short inner linerchecked
- 0406Glued tube with end flaps all round
- 0407Wrap with a double-tucked centre wall
- 0409One-piece tray with glued corners and hinged lid
- 0410Tray with a hinged lid and a tuck lip
- 0411Tray with half-width top flaps and end flaps all roundchecked
- 0413Glued tray with hinged lid and tapered tabs
- 0414Base-locking tray with half-breadth top flapschecked
- 0415Tray with corner tabs and top flaps
- 0416Locking tray with notched top flaps
- 0418Tray and hinged lid with tab-locked ends and lid frontchecked
- 0420Tray with hinged lid, plain corners
- 0421One-piece tray with corner locks and hinged lidchecked
- 0422One-piece tray with base-locking double walls
- 0423Double-wall tray with hinged lid
- 0424Base-locking tray, double front and back walls
- 0425Base-locking tray, double walls all round
- 0426Tray with rounded-front hinged lid
- 0427Roll End Tuck Top mailer (RETT)checked
- 0428Tray with rounded-front side-hinged lid
- 0429Double-wall tray with tuck-front lid
- 0430Tray with returned walls all roundchecked
- 0431Deep tray with double walls and corner locks
- 0432Tray with returned walls and corner slots
- 0433Tray with double walls all round
- 0434Tray with webbed corners and half-width returnschecked
- 0435Double-wall tray with low front
- 0436Shallow locking tray with top flaps
- 0437Tray with webbed corners and partial lid
- 0440Tray and hinged lid with return lips both endschecked
- 0441Tray and hinged lid with a single return lip
- 0442Tray and hinged lid with hook-locked ends
- 0443Slim wrap with corner ears, ears on the back wall
- 0444Slim wrap with corner ears, ears on the front wall
- 0445Mailer with double end walls and hinged lid
- 0446Die-cut bottle and can tray with clinching apertureschecked
- 0447Wrap with a hooked top panelchecked
- 0448Tray with outfolded cornerschecked
- 0449Tray with infolded corner triangleschecked
- 0450Tray with angled end-wall creases and corner ears
- 0451Tray with angled end-wall creases and side-hung ears
- 0451.1Locking version of the side-hung ear tray
- 0452Glued tray, square corner lapschecked
- 0453Glued tray, corner laps on the long wallschecked
- 0454Tray with double side walls and full-width corner earschecked
- 0455Tray, doubled long walls and square corner lapschecked
- 0456Tray with double walls and corner postschecked
- 0457Tray with hooked corners
- 0458Tray with stitched cornerschecked
- 0459Octagonal-base glued tray
- 0460Shelf display bin
- 0461Webbed-corner tray with base-locking side wallschecked
- 0464Locking tray with half-breadth lids and stacking tabschecked
- 0470Wrap-around box with locking lid
- 0471Wrap-around box with rounded locking lid
- 0472Six-panel wrap with self-locking endschecked
- 0473T-shaped wrap with a hook closurechecked
- 0474T-shaped wrap with a plain tuck endchecked
- 0475Tray and lid with a locked front wall and flared endschecked
- 0480Common Footprint stackable tray
Browse every code, or read what the groups mean.
Related
- Every FEFCO code we build — all 244 of them, grouped.
- FEFCO codes explained — what the four digits mean and what each group covers.
- How to measure a box — inside, outside and crease-to-crease.
- Flutes and calipers — why board thickness changes the blank.