FEFCO 0413 Box Template Generator
Glued tray with hinged lid and angled return tabs. A one-piece strip — wall, base, wall, lid, tuck lip — glued at the ends. The base carries a deeper end flap than the walls do, creased again near its tip so the last of it folds back as a return tab, and both corners of that tab are cut away at an angle so it drops between the two glued wall flaps without catching.
Checked against the plate. This blank has been compared side by side with the drawing in the FEFCO Code, 12th Edition, and matches. That is a statement about the drawing, not a guarantee — always cut and fold a sample before committing to a die.
What is FEFCO 0413?
FEFCO 0413 is cut and creased from a single blank that folds up around the product, usually without a glued joint. A one-piece strip — wall, base, wall, lid, tuck lip — glued at the ends. The base carries a deeper end flap than the walls do, creased again near its tip so the last of it folds back as a return tab, and both corners of that tab are cut away at an angle so it drops between the two glued wall flaps without catching.
Uses
- Retail and gift packaging, where the box is seen by the customer
- High-volume packing lines, since a pre-glued blank erects in one movement
Advantages
- Cut from a single blank, so there is one tool and one part to stock
- Arrives glued and flat, and erects quickly by hand or by machine
Disadvantages
- The glued joint sets the minimum order — short runs are rarely economical
Typical industries
- Retail display
Recommended board grades
Single wall B or E flute. E flute where the outside will be printed, since the finer flute takes a cleaner print and creases more sharply.
At a glance
| Code | 0413 |
| Family | Corrugated (FEFCO) |
| Blank size at this size | 623 × 522 mm |
| Panels | 13 |
| Creases | 12 |
Get the dieline
The generator draws this style to whatever dimensions you enter and exports it as a 1:1 PDF, an SVG, or a DXF with the cut, crease and perforation lines on separate layers. Nothing to sign up for.
Open 0413 in the generatorOther folder boxes and trays
Usually one piece of board. The bottom is hinged to form two or all side walls and the cover; locking tabs, handles and display panels can be incorporated.
- 0400Wrap-around folder with an inner bottom linerchecked
- 0401One-piece folder, plain endschecked
- 0402One-piece folder, flaps all roundchecked
- 0403Tray with box-section side wallschecked
- 0404Two crossed folderschecked
- 0405Two crossed folders, short inner linerchecked
- 0406Glued tube with end flaps all roundchecked
- 0407Wrap with a double-tucked centre wallchecked
- 0409One-piece tray with glued corners and hinged lidchecked
- 0410Tray with a hinged lid and a tuck lipchecked
- 0411Tray with half-width top flaps and end flaps all roundchecked
- 0412Folder with tucked-in end wallschecked
- 0414Base-locking tray with half-breadth top flapschecked
- 0415Tray with corner tabs and top flapschecked
- 0416Locking tray with notched top flapschecked
- 0418Tray and hinged lid with tab-locked ends and lid frontchecked
- 0420Tray with hinged lid, plain cornerschecked
- 0421One-piece tray with corner locks and hinged lidchecked
- 0422One-piece tray with base-locking double wallschecked
- 0423Double-wall tray with wrapped cornerschecked
- 0424Base-locking tray, double front and back wallschecked
- 0425Base-locking tray, double walls all roundchecked
- 0426Tray with rounded-front hinged lidchecked
- 0427Roll End Tuck Top mailer (RETT)checked
- 0428Tray with rounded-front side-hinged lidchecked
- 0429Double-wall tray with tuck-front lidchecked
- 0430Tray with returned walls all roundchecked
- 0431Deep tray with double walls and corner lockschecked
- 0432Tray with returned walls and corner slotschecked
- 0433Tray with double walls all roundchecked
- 0434Tray with webbed corners and half-width returnschecked
- 0435Double-wall tray with low frontchecked
- 0436Stacking tray with returned walls and corner lockschecked
- 0437Tray with webbed corners and partial lidchecked
- 0440Tray and hinged lid with return lips both endschecked
- 0441Tray and hinged lid with a single return lipchecked
- 0442Tray and hinged lid with hook-locked endschecked
- 0443Slim wrap with corner ears, ears on the back wallchecked
- 0444Slim wrap with corner ears, ears on the front wallchecked
- 0445Mailer with double end walls and hinged lidchecked
- 0446Die-cut bottle and can tray with clinching apertureschecked
- 0447Wrap with a hooked top panelchecked
- 0448Tray with outfolded cornerschecked
- 0449Tray with infolded corner triangleschecked
- 0450Tray with angled end-wall creases and corner earschecked
- 0451Tray with angled end-wall creases and side-hung earschecked
- 0451.1Locking version of the side-hung ear traychecked
- 0452Glued tray, square corner lapschecked
- 0453Glued tray, corner laps on the long wallschecked
- 0454Tray with double side walls and full-width corner earschecked
- 0455Tray, doubled long walls and square corner lapschecked
- 0456Tray with double walls and corner postschecked
- 0457Tray with hooked cornerschecked
- 0458Tray with stitched cornerschecked
- 0459Octagonal-base glued traychecked
- 0460Shelf display binchecked
- 0461Webbed-corner tray with base-locking side wallschecked
- 0464Locking tray with half-breadth lids and stacking tabschecked
- 0470Wrap-around box with locking lidchecked
- 0471Wrap-around box with rounded locking lidchecked
- 0472Six-panel wrap with self-locking endschecked
- 0473T-shaped wrap with a hook closurechecked
- 0474T-shaped wrap with a plain tuck endchecked
- 0475Tray and lid with a locked front wall and flared endschecked
- 0480Common Footprint stackable traychecked
Browse every code, or read what the groups mean.
Related
- Every FEFCO code we build — all 244 of them, grouped.
- FEFCO codes explained — what the four digits mean and what each group covers.
- How to measure a box — inside, outside and crease-to-crease.
- Flutes and calipers — why board thickness changes the blank.